Click Here To Find Out More

 

 

On this page down the page you'll find a bunch of brilliant information involving How to Install a Bathtub.

Mounting a bath tub isn't exactly rocket science, however it does call for strong plumbing, carpentry, and often, tiling abilities. Changing an old bath tub with a new one is also a moderately tough task. If the old bathtub is conveniently easily accessible, the task can relocate speedily; if you have to open a wall to eliminate the old bathtub and also place the brand-new bath tub, the job is much harder. In either case, the project is within a home handyman's skills, although you will need an assistant to leave the old bathtub as well as embeded in the brand-new one. See to it you have actually certified on your own for the work and also fit attempting it. Rather than hiring a contractor to take over a halfway-completed project, it is better to consider employing one before you begin. Chances are you may require a specialist plumber to make tube links.
This write-up will certainly aid you mount a brand-new tub in your shower room if you have already purchased a new tub and do not require to transform the plan of your previous water system pipes.
Your devices and also product list need to consist of the following:

 

• New Bath tub


• Hammer


• Pipeline Wrenches


• Prybar


• Shatterproof glass


• Degree


• Pliers


• Flexible Wrench


• Putty Blade


• Screwdriver


• Cold Blade


• Tape Measure


• Pipe Caps


 

Removing Old Taps

If you need to change old faucets with new ones as a part of your installation, after that the first thing you need to do is separate the water. After doing so, activate the faucets to drain pipes any type of water remaining in the system. The procedure of getting rid of the existing taps can be quite problematic as a result of the limited access that is often the instance.
Use a container wrench (crowsfoot spanner) or a faucet tool to undo the nut that connects the supply pipes to the taps. Have a towel all set for the continuing to be water that will certainly originate from the pipelines. When the supply pipes have been eliminated, use the very same device to loosen up the nut that holds the taps onto the bath/basin. You will need to quit the solitary taps from transforming throughout this process. As soon as the faucets have been gotten rid of, the holes in the bath/basin will have to be cleaned up of any type of old sealing compound.
Prior to going on to fit the brand-new taps, compare the pipeline connections on the old taps to the brand-new taps. If the old taps are longer than the brand-new taps, after that a shank adapter is needed for the new faucets to fit.

 

 

Fitting New Touches

If the tails of the new faucets are plastic, then you will certainly need a plastic adapter to avoid damage to the string. One end of the connector fits on the plastic tail of the faucet and the other end gives a connection to the existent supply pipelines.
If you need to fit a monobloc, after that you will certainly require lowering couplers, which links the 10mm pipeline of the monobloc to the common 15mm supply pipe.
Next off, position the faucet in the mounting opening in the bath/basin ensuring that the washing machines are in location in between the tap and also the sink. Secure the faucet in place with the maker provided backnut. When the faucet is securely in position, the supply pipes can be linked to the tails of the faucets. The taps can either be linked by using corrugated copper piping or with typical faucet connectors. The former kind should be linked to the faucet ends initially, tightening up only by hand. The supply pipelines can later on be connected to the various other end. Tighten up both ends with a spanner after both ends have been linked.

 

 

Mounting the Bathtub

Making use of both wooden boards under its feet, put the bath tub in the required setting. The wooden boards are handy in evenly spreading out the weight of the bathtub over the area of the boards as opposed to focusing all the weight onto 4 tiny points.
The next objective is to ensure that the tub is leveled all round. This can be attained by inspecting the level and also changing the feet on the bath tub until the spirit level checks out degree.
To install faucets, fit all-time low of the furthest versatile faucet adapter to the suitable supply pipeline by making a compression sign up with; then do the exact same for the various other faucet.
Switch on the water system and also check all joints and brand-new pipework for leakages and tighten them if required. Fill up the bath tub and likewise check the overflow outlet as well as the regular electrical outlet for leaks.
Lastly, take care of the bathroom paneling as described in the manufacturer's instruction manual. Tiling as well as securing around the bath tub should wait until the bathtub has been made use of at least once as this will settle it into its final position.

 

 

Preparing for the Installation

Firstly, the supporting frame supplied with the bath needs to be fitted (if called for) according to the manufacturer's guidelines. Next off, fit the faucets or mixer to the bath tub. When fitting the tap block, it is essential to make sure that if the tap comes with a plastic washer, it is fitted between the bath as well as the faucets. On a plastic bathroom, it is likewise practical to fit a sustaining plate under the faucets system to avoid stress on the tub.
Fit the versatile faucet ports to the bottom of the two taps utilizing 2 nuts as well as olives (often provided with the bathtub). Fit the plug-hole electrical outlet by smearing mastic filler round the sink outlet hole, and after that pass the outlet through the hole in the bathroom. Make use of the nut provided by the maker to fit the plug-hole. Take a look at the plug-hole electrical outlet for an inlet on the side for the overflow pipeline.
Next, fit the end of the flexible overflow pipe to the overflow outlet. After that, screw the pipe to the overflow face which should be fitted inside the bathroom. Make certain you utilize every one of the supplied washers.
Connect the catch to the bottom of the waste electrical outlet on the tub by winding the thread of the waste outlet with silicone mastic or PTFE tape, and screw on the catch to the electrical outlet. Attach all-time low of the overflow tube in a similar manner.The bath should currently prepare to be fitted in its final position.

 

 

Tiling Around the Bathtub

In the area where the bathroom satisfies the ceramic tile, it is necessary to secure the joins with a silicone rubber caulking. This is important as the installation can move sufficient to split a rigid seal, creating the water to permeate the wall between the bathroom and also the tiling, resulting in complications with wetness and also possible leaks to the ceiling listed below.
You can choose from a selection of coloured sealers to blend in your components as well as fittings. They are marketed in tubes as well as cartridges, and can securing gaps approximately a size of 3mm (1/8 inch). If you have a larger void to fill, you can load it with twists of soaked paper or soft rope. Remember to constantly fill up the bathtub with water prior to sealing, to permit the motion experienced when the tub remains in use. The sealer can break rather early if you do not take into account this activity before securing.
Additionally, ceramic coving or quadrant floor tiles can be used to border the bath or shower tray. Plastic strips of coving, which are easy to use as well as reduce to size, are additionally easily readily available on the market. It is recommended to fit the floor tiles using waterproof or water-proof adhesive as well as grout.

 

How to Install or Replace a Bathtub

 

Find Your Dimensions

 

The first step in any bathtub installation or replacement is to select the right size tub for your bathroom. Start by measuring your existing bathtub’s alcove from wall to wall. The standard size for bathtubs is around 5 feet long and 30 or 32 inches wide. Purchase the size that’s closest to your previous tub.

After you’ve measured, you’ll need to figure out what type of tub you need. Face the alcove. If the drain is on the right-hand side, you’ll need a right drain tub. If it’s on the left, get a left drain tub. Easy enough, right?

 

Disconnect the Water Supply and Drain Assembly

 

Before you can start on your removal, make sure that you turn off the tub’s water supply. Some bathrooms have a shutoff valve, but if you don’t see one, you’ll need to turn off the supply at your house’s water main. Once the water’s off, open the valves to release any remaining air in the supply lines.

Then, disconnect the tub drain flange. This process varies based on the type of drain you have, but in most cases, you’ll need a drain flange removal tool to perform this task. If you’re feeling handy, you might be able to use a pair of needle-nose pliers to twist and pull the flange.

Now comes the fun part. In order to disconnect the drain assembly, you’ll need to be able to get to the space underneath the tub. You might need to access the tub drain from a crawlspace or a basement. Don’t forget to take a pipe wrench with you, as you’ll need it to loosen the pipe at the connection.

 

Cut Out the Old Tub

 

After removing the drainpipe assembly, you can take out the old bathtub. Cut a strip above the tub edge in the wall surrounding the bathtub that's about 6 inches in height. The tools you need here may vary depending on the type of wall surround you have in the alcove. If you’re cutting drywall, use a drywall saw and remove the section of the wall all the way down to the studs. If you have tile, you’ll need to use a grinder with a diamond blade to cut through the grout line. Then, use a chisel to remove the individual tiles. Take care here not to cut through any studs.

Find the tub flange. Remove the screws that attach the flange to the studs in the wall. At this point, the tub should be freed from the wall.

Once you’ve removed the flange, use a utility knife to cut away the caulk between the tub and the floor. When this is done, you should be able to lift the tub up and out of the alcove. Keep in mind that, depending on what it’s made of, the old tub could be tremendously heavy. You should plan to have a friend help you move it just in case.

 

Install the New Tub

 

Before you make any adjustments to the area, place the new tub in the alcove to make sure it fits properly and that the tub drain lines up with the P-trap underneath the floor.

Remove it and install a 2 x 4 ledger board. Measure the tub’s flange, then mark that height on the wall. Screw the ledger board to studs in the wall. This will help to support the weight of the tub.

Once the ledger board has been installed, go ahead and secure the drain to the tub. For this step, you’ll need some plumber’s putty. Roll a small amount of putty in your hands and wrap it around the underside of the drain flange. Push the drain into the tub from underneath the tub.

When the drain has been attached, connect the overflow drain. To do this, you’ll place the gasket on the overflow elbow and move it behind the tub. Once that’s on, connect the overflow pipe and the drainpipe, but take care not to overtighten.

 

Secure the Tub

 

After the connections are in, it’s time to set the tub in place. Before you start, make sure the flange lines up with the markings you made in Step 4. Because the ledger board holds the tub in place, it’s important that it matches up. If not, you’ll need to remove it and readjust.

Once your measurements line up, attach the flange to the studs on all three sides of the wall. Please note that you should not screw the flange to the wall. Instead, you should use roofing nails because they won’t rust over time. When the tub is in place, install the baseboard and the molding in front of and around the tub.

Repair and finish off the drywall or tile that you cut in Step 3. If you’re installing a fiberglass bath surround, now’s the time to adhere it to the alcove.

Then, enjoy your tub! While all these steps might seem intimidating, removing and installing a new bathtub is a relatively easy DIY project that can be completed in a single day. And now, when you settle in for your next bubbly soak, you can enjoy your bath without the distraction of a tub in disrepair.

https://www.homeserve.com/en-us/blog/how-to/bathtub-replacement/

 

We had been shown that write-up on Tools You Need to Install a New Bathtub through a good friend on another website. Are you aware of another person who is in to A Step-by-Step Guide to Installing a Bathtub? Be sure promote it. Thanks a lot for your time spent reading it.

Course Detail